zlacker

>>xairy+(OP)
I thought the whole point of these camera LEDs was to have them wired to/through the power to the camera, so they are always on when the camera is getting power, no matter what.

Having the LED control exposed through the firmware completely defeats this.

>>sbarre+T1
They are hardwired on Macbooks. From Daring Fireball, quoting an email from an Apple engineer.

> All cameras after [2008] were different: The hardware team tied the LED to a hardware signal from the sensor: If the (I believe) vertical sync was active, the LED would light up. There is NO firmware control to disable/enable the LED. The actual firmware is indeed flashable, but the part is not a generic part and there are mechanisms in place to verify the image being flashed. […]

> So, no, I don’t believe that malware could be installed to enable the camera without lighting the LED. My concern would be a situation where a frame is captured so the LED is lit only for a very brief period of time.

https://daringfireball.net/2019/02/on_covering_webcams

>>542458+96
>The actual firmware is indeed flashable, but the part is not a generic part and there are mechanisms in place to verify the image being flashed.

That might make it harder to develop a hack, but one would hope that if the hardware team tied the LED to a hardware signal, it would not matter if the firmware were reflashed.

>>aftbit+U7
I believe that it’s not literally hardwired in the sense that powering up the camera also powers up the camera LED, and instead this relies on logic in the hopefully un-flashable camera+LED firmware. Someone correct me if I’m wrong.

You need some logic to enforce things like a minimum LED duration that keeps the LED on for a couple seconds even if the camera is only used to capture one brief frame.

I have a script that takes periodic screenshots of my face for fun and I can confirm the LED stays on even if the camera only captures one quick frame.

>>varenc+I8
I happen to have some first-hand knowledge around the subject! In 2014 someone did a talk[0] on disabling the camera on some older Macbooks. It was fairly trivial, basically just reflashing the firmware that controlled the LED. I worked on the security team at Apple at the time and in response to this I attempted to do the same for more modern Macbooks. I won't go into the results but the decision was made to re-architect how the LED is turned on. I was the security architect for the feature.

A custom PMIC for what's known as the forehead board was designed that has a voltage source that is ALWAYS on as long as the camera sensor has power at all. It also incorporates a hard (as in, tie-cells) lower limit for PWM duty cycle for the camera LED so you can't PWM an LED down to make it hard to see. (PWM is required because LED brightness is somewhat variable between runs, so they're calibrated to always have uniform brightness.)

On top of this the PMIC has a counter that enforces a minimum on-time for the LED voltage regulator. I believe it was configured to force the LED to stay on for 3 seconds.

This PMIC is powered from the system rail, and no system rail means no power to the main SoC/processor so it's impossible to cut the 3 seconds short by yoinking the power to the entire forehead board.

tl;dr On Macbooks made after 2014, no firmware is involved whatsoever to enforce that the LED comes on when frames could be captured, and no firmware is involved in enforcing the LED stay on for 3 seconds after a single frame is captured.

0: https://www.usenix.org/system/files/conference/usenixsecurit...

>>axoltl+Lh
I've seen a million people parroting "oh now apple fixed it!" and not a single person who has actually verified/proved it. Go on, show my any third party security researcher who has verified this claim via examining the actual hardware.

You'll pardon us all if we don't really believe you, because a)there's no way for any of us to verify this and b)Apple lied about it before, claiming the LED was hard-wired in blah blah same thing, except it turned out it was software controlled by the camera module's firmware.

>>KennyB+xJ
> Apple lied about it before, claiming the LED was hard-wired in blah blah same thing, except it turned out it was software controlled by the camera module's firmware.

Source?